Black Box Computer Hardware IC113C User Manual

MARCH 2000  
IC113C  
IC175C  
Dual Port RS-232/422/485 Serial Interface  
CUSTOMER Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX  
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746  
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018  
SUPPORT  
INFORMATION  
 
DUAL PORT RS-232422/485 SERIAL INTERFACE  
NORMAS OFICIALES MEXICANAS (NOM)  
ELECTRICAL SAFETY STATEMENT  
INSTRUCCIONES DE SEGURIDAD  
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes  
de que el aparato eléctrico sea operado.  
2. Las instrucciones de seguridad y operación deberán ser guardadas para  
referencia futura.  
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de  
operación deben ser respetadas.  
4. Todas las instrucciones de operación y uso deben ser seguidas.  
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,  
cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,  
etc..  
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales  
que sean recomendados por el fabricante.  
7. El parato eléctrico debe ser montado a la pared o al techo sólo como sea  
recomendado por el fabricante.  
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más  
allá a lo descrito en las instrucciones de operación. Todo otro servicio  
deberá ser referido a personal de servicio calificado.  
9. El aparato eléctrico debe ser situado de tal manera que su posición no  
interfiera su uso. La colocación del aparato eléctrico sobre una cama,  
sofá, alfombra o superficie similar puede bloquea la ventilación, no se  
debe colocar en libreros o gabinetes que impidan el flujo de aire por los  
orificios de ventilación.  
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de  
calor como radiadores, registros de calor, estufas u otros aparatos  
(incluyendo amplificadores) que producen calor.  
 
NOM STATEMENT  
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo  
del tipo descrito en el instructivo de operación, o como se indique en el  
aparato.  
12. Precaución debe ser tomada de tal manera que la tierra fisica y la  
polarización del equipo no sea eliminada.  
13. Los cables de la fuente de poder deben ser guiados de tal manera que no  
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,  
poniendo particular atención a los contactos y receptáculos donde salen  
del aparato.  
14. El equio eléctrico debe ser limpiado únicamente de acuerdo a las  
recomendaciones del fabricante.  
15. En caso de existir, una antena externa deberá ser localizada lejos de las  
lineas de energia.  
16. El cable de corriente deberá ser desconectado del cuando el equipo no  
sea usado por un largo periodo de tiempo.  
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean  
derramados sobre la cubierta u orificios de ventilación.  
18. Servicio por personal calificado deberá ser provisto cuando:  
A: El cable de poder o el contacto ha sido dañado; u  
B: Objectos han caído o líquido ha sido derramado dentro del  
aparato; o  
C: El aparato ha sido expuesto a la lluvia; o  
D: El aparato parece no operar normalmente o muestra un cambio en su  
desempeño; o  
E: El aparato ha sido tirado o su cubierta ha sido dañada.  
 
DUAL PORT RS-232422/485 SERIAL INTERFACE  
Contents  
Chapter  
Page  
1. Specifications...................................................................................................1  
2. Introduction....................................................................................................2  
2.1 Overview..................................................................................................2  
2.2 What’s Included......................................................................................2  
2.3 Features ...................................................................................................3  
2.4 Technical Description ............................................................................4  
3. Address Selection............................................................................................6  
4. Option Selection.............................................................................................7  
4.1 Port Enable/Disable...............................................................................7  
4.2 RS-232 Interface Options .......................................................................9  
4.3 RS-422/485 Interface Options.............................................................10  
4.4 Line Termination .................................................................................11  
5. Installation.....................................................................................................12  
Appendix: Circuit-Board Design.......................................................................14  
 
CHAPTER 1: Specifications  
1. Specifications  
Protocol — Asynchronous  
Speed — IC113C: Up to 115.2 Kbps; IC175C: 460.8 kbps and higher  
Operation — RS-232 or RS-485/422, 2- or 4-wire (individually selectable  
on each port)  
Connectors — (2) DB9M  
Communications Chip — IC113C: 16550 UART; IC175C: 16950 UART  
MTBF — >150,000 hours  
MTTR — <0.25 hours  
Materials — Boards are solder mask over bare copper or tin nickel  
Operating Temperature — 32° to 122°F (0° to 50°C)  
Storage Temperature — -4° to 158°F (-20° to 70°C)  
Humidity — 0 to 90% relative humidity, noncondensing  
Power — +5 VDC @ 195 mA 12 V @ 25 mA (derived from PC bus)  
Size — 5"W x 7.5 "D (12.7 x 19 cm)  
Weight — 0.2 lb. (0.1 kg)  
1
 
DUAL PORT RS-232422/485 SERIAL INTERFACE  
2. Introduction  
2.1 Overview  
If you need to operate RS-232, RS-422, or RS-485 devices from your PC, use  
the Dual Port RS-232/422/485 Serial Interface. Connect to any device that  
uses the RS-232 interface, such as modems, data-entry terminals, and plotters.  
This card allows you to configure two RS-232 ports, two RS-422/485 ports, or  
one of each. The Dual Port RS-232/422/485 also features greater maximum  
distance and allows multi-drop communications.  
The card also includes a serial utility disk with Seacom, a DOS interrupt and  
driver package. Seacom allows data to be buffered, eliminating data loss in  
high-speed data transfers. It also allows more than 4 ports (256 max.) to be  
configured and utilized under DOS.  
The README file on the serial utility disk contains information about the  
latest changes and revisions. To view this file, insert the diskette into drive A  
or B and type A:TYPE READ.ME|MORE [ENTER]or B:TYPE  
READ.ME|MORE [ENTER].  
2.2 What’s Included  
Your Serial Interface should come with the following items. If any of these  
items are missing or damaged, contact Black Box at 724-746-5500.  
(1) Dual Port RS-232/422/485 Serial Interface card,  
®
(2) serial utility software diskettes: (1) for 32-bit Windows ,  
®
(1) for DOS and Windows 3.1x,  
This manual  
2
 
CHAPTER 2: Introduction  
2.3 Features  
Listed below are the special features your Serial Interface offers.  
• Each port is independently addressable.  
• Eleven interrupt options, including AT interrupts, for simple integration  
into existing systems.  
• IRQs (2 [9], 3, 4, 5, 6, 7, 10, 11, 12, and 15) supported.  
• IRQs can be shared or individually set for each port.  
• Supports Interrupt Sharing—only one interrupt line required for  
multiple ports.  
• Supports any character set defined by binary notation.  
• 16550 UARTs on the IC113C help ensure against data loss. This chip  
features programmable baud rate, data format, interrupt control, and a  
16-byte FIFO. The IC175C uses 16950 UARTs, which feature a 128-byte  
buffer for even better performance.  
• Faster baud rates—up to 115.2 Kbps (IC113C) or 460.8 kbps and above  
(IC175C).  
• Addressable as COM1: through COM4: or any other address up  
to 3FF Hex.  
• Support for non-standard baud rates available. These baud rates (such as  
31.25K or 76.8K baud) are supported by installing a different oscillator at  
location Y1. Call Technical Support for more information.  
3
 
DUAL PORT RS-232422/485 SERIAL INTERFACE  
2.4 Technical Description  
The Dual Port RS-232/422/485 Serial Interface utilizes the same 16550 UART  
®
chip found in the IBM asynchronous adapter. This chip features  
programmable baud rate, data format, and interrupt control. Refer to the  
IBM Technical Reference for details on programming the chip.  
RS-232  
The Dual Port RS-232/422/485 Serial Interface meets the RS-232C  
specifications and provides an asynchronous serial I/O port. This is the  
®
standard port configuration found in the IBM AT computer, including the  
DB9 style connector.  
The table below shows the connector pinouts for ports J1 (port 1) and J2  
(port 2) on the Interface while using RS-232.  
Pin Number  
Signal Name  
Mode  
3
7
4
5
2
1
6
8
9
Transmit Data (TD)  
Request To Send (RTS)  
Data Term Ready (DTR)  
Ground (GND)  
Output RS-232  
Output RS-232  
Output RS-232  
––––––––––––  
Input RS-232  
Input RS-232  
Input RS-232  
Input RS-232  
Input RS-232  
Receive Data (RD)  
Data Carrier Detect (DCD)  
Data Set Ready (DSR)  
Clear To Send (CTS)  
Ring Indicator (RI)  
RS-422  
RS-422 allows very long distance communications—4000 feet (about  
1219 meters) at 9600 baud—based on use of Category 3, UTP, or better, with  
virtually error-free differential drive characteristics. RS-422 signal levels are  
the standard electrical specification used in RS-449 and EIA-530. This allows  
interfacing with equipment that meets these specifications.  
4
 
CHAPTER 2: Introduction  
RS-485  
RS-485 is backward-compatible with RS-422; however, it is optimized for  
multidrop applications. The output of the RS-422/485 driver is capable of  
being active (enabled) or tri-state (disabled). This capability allows multiple  
ports to be connected in a multidrop bus and selectively polled. Half-duplex  
two-wire communications are possible by connecting TX+ to RX+ and TX- to  
RX- in your cable connector. The enable to the driver is connected to the  
UART Request To Send (RTS) line for RS-485 communications. This allows  
the RS-485 driver to be tri-stated (disabled) when inactive on a multidrop  
polled network. The software that you are using must “know how” to enable  
the driver when it is answering a poll. Failure to set this jumper correctly can  
cause transmitter contention problems, preventing operation by any nodes on  
the network.  
The table below shows the connector pinouts for ports J1 (port 1) and J2  
(port 2) on the Interface while using RS-422/485.  
Pin Number  
Signal Name  
Mode  
4
3
6
7
5
1
2
9
8
Transmit Data Pos. (TX+)  
Transmit Data Neg. (TX-)  
Req. To Send Pos. (RTS+)  
Req. To Send Neg. (RTS-)  
Ground (GND)  
Output RS-422  
Output RS-422  
Output RS-422  
Output RS-422  
--------------------  
Input RS-422  
Input RS-422  
Input RS-422  
Input RS-422  
Receive Data Pos. (RX+)  
Receive Data Neg. (RX-)  
Clear To Send Pos. (CTS+)  
Clear To Send Neg. (CTS-)  
5
 
DUAL PORT RS-232422/485 SERIAL INTERFACE  
3. Address Selection  
NOTE  
Be sure to set the address selections and jumper options before  
installation.  
Each serial port on the Dual Port RS-232/422/485 Serial Interface occupies  
8 consecutive I/O locations. DIP switch SW1 sets the base address for Port 1,  
and DIP switch SW2 sets the address for Port 2. Be careful when selecting the  
base address, since some selections conflict with existing PC ports. The  
following table shows several examples that usually do not cause a conflict.  
Address  
Hex  
Binary  
Switch Position Setting  
A9  
A0  
1
2
3
4
5
6
7
280-287 1010000XXX OFF  
2A0-2A7 1010100XXX OFF  
2E8-2EF 1011101XXX OFF  
2F8-2FF 1011111XXX OFF  
3E8-3EF 1111101XXX OFF  
300-307 1100000XXX OFF  
328-32F 1100101XXX OFF  
3F8-3FF 1111111XXX OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
Typically COM1:=3F8h; COM2:=2F8h; COM3:=3E8h; COM4:=2E8h  
The following illustration shows the correlation between the DIP switch  
setting and the address bits used to determine the base address. In the figure  
below, the address 300 hex through 307 hex is selected (300 hex =11 0000  
0XXX in binary representation). Note that setting the switch ON (or closed)  
corresponds to a “0” in the address, while leaving it OFF (or open)  
corresponds to a “1.”  
A9  
A3 EN  
0
1
ON  
OFF  
1
2
3
4
5
6
7
8
6
 
CHAPTER 4: Option Selection  
4. Option Selection  
NOTE  
Be sure to set the address selections and jumper options before  
installation.  
The board contains several jumper straps for each port which must be set for  
proper operation.  
4.1 Port Enable/Disable  
Each port on the Dual Port RS-232/422/485 can be enabled or disabled with  
switch position 8 on the DIP switch. The port is enabled with the switch ON  
(or closed) and disabled when OFF (or open). If any port is disabled, be sure  
to also disable the interrupt request for that port by removing the IRQ jumper  
(see Figure 4-1).  
INTERFACE SELECTION  
RS-422/485  
To select the RS-422/485 mode of operation, install DIP shunts in sockets  
found at E6 and E7. E6 sets Port 1 and E7 sets Port 2.  
RS-232  
To select the RS-232 mode of operation, install DIP shunts in sockets found  
at E5 and E8. E5 sets Port 1 and E8 sets Port 2.  
IRQ Selection  
Headers E1 and E2 select the interrupt request for each serial port (E1–Port  
2, E2–Port 1). If COM1: is selected, this jumper must be on the IRQ4 setting.  
If COM2: is selected, this jumper must be on IRQ3.  
NOTE  
Most communications software applications default COM3: to IRQ4 and  
COM4: to IRQ3. This requires the sharing of interrupts between COM1:  
and COM3:, and between COM2: and COM4:. While this is the default, it  
is not always the best setting. Check your software configuration  
instructions to determine the most appropriate IRQ setting.  
7
 
DUAL PORT RS-232422/485 SERIAL INTERFACE  
E1  
2/9 3 4 5 7 10 11 12 15  
E2  
2/9 3 4 5 7 10 11 12 15  
Figure 4-1. Header E1 and E2 (IRQ selection).  
Any two or more ports can share a common IRQ by placing the jumpers on  
the same IRQ setting, and setting the appropriate selections at E9 and E10.  
Consult your particular software for IRQ selection. If no interrupt is desired,  
remove the jumper.  
NOTE  
IRQ 2 on AT class machines is not available. IRQ 9 is substituted in place  
of IRQ 2. To select IRQ 9, place jumper in the IRQ 2 position.  
Figure 4-2 shows Headers E9 and E10. “N” indicates the normal, single  
interrupt per port mode. The “S” indicates the shared interrupt mode, which  
allows more than one port to access a single IRQ. The “M” indicates that the  
inclusion of a 1K-ohm pull-down resistor is required on one port when  
sharing interrupts. E10 sets Port 1 and E9 sets Port 2.  
8
 
CHAPTER 4: Option Selection  
Figure 4-2. Headers E9 and E10 in Normal Mode.  
Set jumpers to “N” for single interrupt mode. This setting is the normal  
setting for most applications.  
Set jumpers to “S” for shared interrupt mode for all ports sharing an IRQ  
except one. Set that port block for “M.” This provides the pull-down resistor  
circuit that makes sharing of IRQ’s possible. If you are using more than one Dual  
Port RS-232/422/485 Serial Interface or a compatible card in a bus, you should only  
have one port set to “M.”  
Set jumpers to “S” if you are using more than one Dual Port  
RS-232/422/485 in a bus or if you wish to completely remove the pull-down  
resistor for hardware compatibility. Setting the board in this configuration  
when it is not accompanied by a pull-down resistor will prevent the ports from  
triggering an interrupt.  
4.2 RS-232 Interface Options  
To select the RS-232 mode of operation, install DIP shunts in the sockets  
found at E5 and E8. E5 sets Port 1 and E8 sets Port 2. These DIP shunts are  
completely independent of each other, allowing the user to select a single-  
port RS-232 or a single-port RS-422.  
There are no modem control options for the RS-232 interface: all control  
signals are implemented. If your software requires certain handshaking  
signals to be active, then you must connect them either to the device with  
which you are communicating or you can satisfy the handshake signal  
requirements by connecting pins 7 to 8 (RTS to CTS) and pins 4 to 6 to 1  
(DTR to DSR & DCD). Make these connections on the DB9 connector that  
connects to each port. Refer to Figure 4-3 when making these connections.  
(The table on page 4 lists the RS-232 pinout descriptions.)  
9
 
DUAL PORT RS-232422/485 SERIAL INTERFACE  
5
4
3
2
1
9
8
7
6
Figure 4-3. DB9 Handshake Loopback connections for RS-232  
(shown from rear or cable side of connector).  
4.3 RS-422/485 Interface Options  
To select the RS-422/485 mode of operation, install DIP shunts in the sockets  
found at E6 and E7. E6 sets Port 1 and E7 sets Port 2.  
Figure 4-4 shows Headers E3 and E4. Position “A” determines whether the  
RS-485 driver is enabled by the UART signal Request To Send (RTS) or always  
enabled. With the jumper installed in position “A,” RTS enables the driver.  
Removing the jumper enables the driver, regardless of RTS. E4 sets Port 1  
and E3 sets Port 2. This jumper should be set to “A” only if you are running  
the board in a multidrop polled environment such as RS-485, and you have  
software that “knows how to talk” on the RS-485 bus. For normal point-to-  
point RS-422 (such as terminal emulation), make sure that a jumper at  
position “A” is not in place.  
Positions “B” and “C” determine whether the board provides a direct ground  
connection (as in RS-232 and most RS-422), or a 100-ohm high-impedance  
ground. The high-impedance ground is normally used by  
RS-485 (and some RS-422) to avoid ground-loop currents with long cables.  
Position “B” selects the direct ground, and position “C” selects the 100-ohm  
high-impedance ground. “C” should be selected when RS-422/485 operation  
is selected.  
10  
 
CHAPTER 4: Option Selection  
Figure 4-4. Headers E3 and E4, RS-485 Enable/Ground Selection.  
4.4 Line Termination  
Typically each end of the RS-422/485 bus must have line-terminating  
resistors. A 100-ohm resistor is across each RS-422/485 input, and a 1K-ohm  
pull-up/pull-down combination biases the receiver inputs. If more than two  
RS-485 nodes are configured in a multidrop network, only the nodes at each  
end of the bus should have the 100-ohm resistors installed.  
11  
 
DUAL PORT RS-232422/485 SERIAL INTERFACE  
5. Installation  
The Dual Port RS-232/422/485 can be installed in any of the PC expansion  
®
slots, except J8 on the original IBM XT and Portable.  
IMPORTANT  
You MUST set up the operating system BEFORE you physically install  
the Card.  
5.1 Software Installation  
®
If you are installing an ISA adapter in DOS, OS/2 , or QNX, please refer to the  
appropriate directory on one of the Serial Utilities Disks for instructions.  
5.1.1 WINDOWS 3.1X  
Please refer to the /WINDOWS sub-directory on the Serial Utilities Diskette for  
help files and current information on the installation of the Card in this operating  
environment.  
5.1.2 WINDOWS 95/98 USERS  
For the ISA card, run setup on disk two of the Serial Utilities Diskettes before  
installing the card. Make note of the resources that Windows assigns the adapter,  
and set the adapter to match those resources. Power down the computer and  
install the adapter as described in Section 5.2. If you wish to change any resources  
assigned to the adapter, refer to the help file installed in the Black Box folder in  
the Start, Programs menu.  
5.1.3 WINDOWS NT  
For the ISA card, run setup on disk two of the Serial Utilities Diskettes before  
installing the card. After installing the software, refer to the help file that  
automatically comes up for installation instructions.  
12  
 
CHAPTER 5: Installation  
5.2 Hardware Installation  
The ISA Card can be installed in any of the PC expansion slots. The Card contains  
several jumper straps for each port that you must set for proper operation.  
1. Turn off PC power. Disconnect the power cord.  
2. Remove the PC case cover.  
3. Locate an available slot and remove the blank metal slot cover.  
4. Gently insert the Card into the slot. Make sure that the Card is seated  
properly.  
5. Replace the screw.  
6. Replace the cover.  
7. Connect the power cord.  
Installation is complete.  
Self-Test  
To perform a self-test on the card, connect the transmit and receive data pins  
together. If running 422/485, make sure the plus leads are not connected to  
the minus leads. Execute the SLT program provided on the supplied utility  
diskette.  
13  
 
DUAL PORT RS-232422/485 SERIAL INTERFACE  
Appendix: Circuit-Board Design  
9
5
6
1
9
5
6
1
J 1 P O R T 1  
J 1 P O R T 2  
C 1 0  
U 1 3  
U 1 2  
C 9  
E 5  
E 7  
E 8  
E 6  
P 3  
P 1  
R 8  
R 9  
U 9  
U 8  
1
U 1  
C 8  
U 1 8  
R P 3 R P 2  
R P 4  
U 6  
C 7  
P O R T 1  
U 7  
1 5  
1 2  
1 1  
1 0  
6
1 5  
E 4  
1 2  
1 1  
1 0  
6
C
B
A
R 6  
5
5
C
B
A
4
4
3
3
R 5 R 4  
D 2  
E 1 0  
D 1  
R 3  
2
2
R 7  
E 9  
P O R T 2  
P O R T 1  
R P 1  
P O R T 2  
U 3  
E 2  
E 1  
E 3  
C 6  
P 2  
P 6  
R 2  
S W 2  
U 2  
C 2  
C 3  
U 1  
R 1  
S W 1  
U 5  
U 4  
V 1  
C 5  
C 1  
C 1  
14  
 
APPENDIX: Circuit-Board Design  
1
2
R 2  
R P 1  
R P 1  
R P 1  
1
2
R 1  
E 9  
E 1 0  
1
2
3
4
1
2
3
4
15  
 
DUAL PORT RS-232422/485 SERIAL INTERFACE  
1
6
1
8
1
5
1
3
R P 3  
R P 3  
R P 3  
R P 3  
7
8
5
6
3
4
2
1
R P 4  
R P 4  
R P 4  
R P 4  
16  
 
© Copyright 2000. Black Box Corporation. All rights reserved.  
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746  
 

Black Box Cable Box KV7020A User Manual
Blanco Indoor Furnishings 157 040 User Manual
Blue Rhino Charcoal Grill CBT626A User Manual
BMW Automobile Parts 733i User Manual
Bushnell Watch 70 0002 User Manual
Califone Mouse KM TI User Manual
Canon Camera Flash 133 D User Manual
Casablanca Fan Company Outdoor Ceiling Fan 99087 User Manual
Charles Bentley Son Battery Charger AA Series User Manual
Chicago Electric Chainsaw Sharpener 91995 User Manual